Estudio de caso de dragado de Kerr-McGee

Estudio de caso de dragado de Kerr-McGee

Application: Clean and dredge paint pigment residuals

Dredge Used: EDE 7MAU Series Mud Cat™ Dredge

Project Summary: Electric manned automated dredge with 3 Krebs cyclones with a capacity of 2,100 gpm, magnetic flow meter to monitor pump performance, slurry density meter to maintain consistent percent solids by varying traverse speed, and Bottom Sense™ (automated system to detect and protect pond bottom) to follow the contour of the pond and protect the liner.

Machinery Specifications: Mud Cat™ DREDGE, 7MAU SERIES MODEL Manned Electric Dredge with On-Board Solids Separation

General:
Length 47′-l0″ (14.58 m)
Width 13′-6″ (4.11 m)
Height 17′-1″ (Top of Overflow) (5.18 m)
Weight 62,000 lbs. (operational) (18,123 Kilos)
Draft. 2′-11″ (.9 m)

Flotación:
Catamaran Type Hull–Two Pontoons-56″ x 48″ x 40′ -0″ made from 1/4″ thick steel plate with Internal Bulkheads and Stiffeners, Polyurethane foam filled.

cortador:
Auger Type with Shroud

Asamblea:
Diameter (HeIix) 18-3/4″
Diameter (Knife Profile) 24-1/4″
Pitch 11″
Flighting 3/8″
Speed Variable to 60 RPM
Cutter Knives Detachable heat-treated blades
Cutter Torque Variable to 17.200 in.-lb.

Working: Cut 13′-6″ wide x l8″ deep (4.11 m)

Capacity: Digging depth-26′ maximum (7.9 m)

Power: 200 HP TEFC Motor – Dredge Pump, Underflow Pump
Service Water Pump and Ancillary Hydraulic Circuits

Bombas:
End Suction Centrifugal with Semi-open Impeller
Dredge Pump ~10″ x 8″ rubber lined with 22″ diameter impeller
Variable speed – 0 to 600 RPM
Design Capacity-2,l00 GPM @. 17 PSIG at cyclone inlet
Underflow Pump 4″ x 3″ rubber lined with 14″ diameter impeller
Variable speed ~ to 1200 RPM
Design Capacity-250 GPM @ 120 ft. head
Service Water Pump 2′ x 2′ self priming
Variable speed-0 to 2700 RPM
Design Capacity-50 GPM @ 120 ft. head

Solids: Three Krebs Model Dl5LB-T123 Cyclones

Separation: Capacity-2,100 GPM (700 GPM per cyclone)

Hydraulic: Slurry pump – Heavy Duty Hydrostatic Drive
All Other Circuits – Pressure-Volume Gear Pump

Sistemas:
Fixed Displacement Hydraulic Motor(s)
Capacity-7O GPM @ 1750 RPM Motor Speed
Reservoir-75 Gallons
Circuit One-Auger Drive
Circuit Two-Boom Hoist
Circuit Three-Traverse Winch
Circuit Four-Slurry Pump Drive

Relief Pressure Settings:
Slurry Pump Circuit – 4,500 PSI
All other circuits – 2,700 PSI

Propulsión:
Treble Sheave Hydraulic Winch
Traverse Speed – 0 to 100 FPM
Cutting Speed, Nominal – 8 to 12 FPM

Electrical System: Voltage-480V, 3-phase
Two Control Voltage Transformer(s)
120V fuente de alimentación
4V fuente de alimentación

Automatización:
Operation Fully Automated with Monitors feeding Program Logic Control
Dredge Pump – 8″ Slurry Flow Meter Monitors Output/Sets Speed
Traverse Winch-8″ Slurry Density Meter sets speed
Underfiow Pump -Level Control sets speed; Flow Meter Monitors Output
Service Water Pump – 4″ Density Meter starts and stops pump
Cyclone Sump–Level Control signals Underflow Pump
Auger Position–Bottom Sense follows bottom contour–Boom up or down

Para el apanado:
Immersed Surfaces – epoxy coating, 15 mils min. thickness
All other surfaces – Polyurethane enamel on a corrosion inhibitive primer, 5 mils min thickness

¿Desea obtener más información sobre esta historia o hablar con un representante de Mud Cat sobre su proyecto de dragado?

Artículos Relacionados

Logotipo de Ellicott Dredge Enterprises

22 al 25 de febrero 2026

Salt Lake City, Utah

Logotipo de Ellicott Dredge Enterprises

3-7 de Marzo 2026

Las Vegas, Nevada

Utilice el código: ELL5455C